Ground-engaging wear part · Interface-led replacement
M60E bucket-tooth reference
FIORM’s dedicated page identifies M60E with a catalogue photograph. It does not establish a complete adapter-pocket drawing, retaining set or material grade; a replacement needs those details together.
The M60E label starts the enquiry
It does not finish the compatibility check.
The official page names M60E and shows a marked tooth photograph. Its catalogue navigation includes equipment-brand categories, but the retrieved entry contains no controlled adapter drawing, pocket dimensions, material grade or complete retaining-set designation. [1] No compatible machine list is inferred from those navigation headings.
What to identify on the installed assembly
Record the adapter reference, tooth marking/profile and pin orientation. Include images of the complete adapter and retention arrangement, not only the removed tooth.
What the supplier should return
A drawing and exact replacement references linking the proposed tooth to the adapter, pin and retainer. Ask whether the existing adapter remains suitable or a separate adapter change is proposed.
Wear can alter the old pocket and pin arrangement. Measured worn dimensions are evidence of condition, not automatically the original nominal design. Mark whether each measurement comes from a drawing, an unworn reference or a used part.
Compare tooth-only with a complete set
FIORM’s company scope explicitly includes teeth, pins and rubber retaining pieces, while its wider catalogue has separate wear-part/system routes. [2] [3] That makes set definition important; it does not prove a particular pin is included with M60E.
| Quote line | Required identification | Open question |
|---|---|---|
| M60E tooth | Drawing revision, pocket/interface and profile | Does the selected version match the installed adapter? |
| Pin / retaining piece | Part reference, dimensions and quantities | Included, optional or reused under an approved arrangement? |
| Adapter | Existing/new reference and supplier compatibility response | Is the quote a tooth replacement or an adapter conversion? |
| Field spares | Replacement retainer references and pack quantities | What accompanies each replacement tooth and what is spare stock? |
A tooth-only unit price and a tooth-plus-retainer price describe different purchases. Keep the scope next to the price so the comparison does not discard necessary retention parts. Installation must follow the responsible supplier/equipment instructions; this guide is not a fitting procedure.
Select the material against the work
The catalogue photograph contains no test certificate.
FIORM reports materials development for different working conditions, with chemistry, metallographic, impact, wear and flaw-detection equipment. [2] None of those resources establishes M60E’s alloy, heat treatment, hardness or a passing batch.
- Describe the working materialState abrasive material, impact/shock conditions and the observed failure of the current tooth. Avoid requesting “best wear resistance” without describing the job.
- Obtain the proposalAsk for the exact grade and treatment with relevant acceptance values and methods. If a different profile is offered, request a separate fit and application explanation.
- Connect the batch to the evidenceAgree traceability and test reports for the actual supply. A generic wear claim needs its conditions and comparator; it is not a service-life promise on your bucket.
Write the trial record before judging life
An initial trial should identify the installed adapter condition, tooth/retainer references and material proposal, then record actual working material and exposure. Agree observation intervals and replacement criteria with the responsible operator. This allows fit, retention and wear observations to be separated.
No CivilEquip field test or verified M60E wear-life result is available. A photograph after an unknown period cannot establish a meaningful comparison. When evaluating a replacement against an existing tooth, keep the duty and starting condition explicit; differences in those conditions should not be presented as a supplier’s performance advantage.
Does the catalogue’s equipment-brand category prove OEM authorisation?
No. Ask for the precise replacement cross-reference and its fit evidence. If OEM/authorised status is claimed commercially, request its documentary basis separately.
Can the existing retaining components always be reused?
The public M60E entry does not establish that. Ask the supplier to define the compatible set and follow the approved replacement instructions and condition checks.
Send the adapter and retention evidence
Sources & review
- Official M60E entry ↗
Named reference, photograph and category navigation; no controlled dimensions, weight, material or fit rating adopted.
2026-10-11 - FIORM company and material-development description ↗
Tooth, pin and rubber-retainer scope and reported test equipment; no M60E batch result.
2026-10-11 - FIORM system and wear-part catalogue ↗
Separate system/brand categories and retention/wear-part references; authorisation not established.
2026-10-11
Specifications come from the manufacturer’s published information and the sources above; buying advice is written by CivilEquip with AI assistance. Ask the manufacturer to confirm the data for your configuration. Editorial policy · Report a correction.